Latest Posts
Showing topics posted in for the last 365 days.
- Today
-
Well i replaced the hub assembly, and yes i got all my gauges back. Went to try to check speedo works, and found battery didn't have enough to start the car. so after a good charge, i put battery back. Car started first pull, but i have no gauges, and no speedo and rev counter again. Any ideas would be appreciated thanks.
-
That's a nice looking beast you have there. Not my favorite colour, but it does make it stand out.
-
Hi there Johndoh. Welcome to the forum. I am sure you will find lots of interesting stuff on here. Feel free to post any questions you might have. And if you've had an issue that you've managed to sort yourself, you can share your knowledge. Regards Andy.
-
I have a 2008 Corsa D automatic that quite frequently gets stuck in park. An engineer at work had a look. Solder on micro switch to left of gear selector looks fine but he thinks the micro switch the wires are attached to there may be at fault. Would anyone know the part number for this so I can order one. The photo shows the part I'm talking about but it is not a photo from my car
-
- corsa d
- micro switch
-
(and 3 more)
Tagged with:
-
Well here's an update on wheel bearing and speedo. When I fitted the new bearing the other day, I had all gauges working. The car has sat on the drive for a couple of days due to a flat battery. Got her going this morning, and all gauges are not working again. Temp gauge sits twitching, but no other movement. If anyone had any ideas of the next step. Please please help me. Can't get mot until this problem is fixed.
- Yesterday
-
1,drivers window switch only works when it wants to, would this be a window motor or switch problem as the passenger switch works fine, 2, keep getting message on screen that he coolant is low to top up took a look at it and it was a little low so topped up and still get he message done a check for leaks no obvious signs of any leaks
-
Rear set Removal Crossland 2018
Andrew Mason posted a topic in Vauxhall Crossland & Grandland X Club
Can anyone help me... I've had an environmental disaster in the boot of my Crossland. 2 pints of milk were spilt. I removed the floor covering and the spare wheel and I have washed everything several times but I still have a stale milk smell. I wondered if some milk has gone underneath the back seat but I can't find out how to remove the seat to check. - Last week
-
I've been looking for a rear valance or diffuser with an area pre cut out for an exhaust. However I'm struggling to find any. Do they actually make them for my model vehicle?? ( mk1 hatchback insignia pre facelift)
-
Engine Coolant Temperature Sensor on 2019 Vauxhall Insignia
Nick_Nuneaton replied to StuTur's topic in Vauxhall Insignia Club
Have a look on Ebay, I payed about ÂŁ13 for myn. -
Glass roof has stress fracture
jayne britton posted a topic in Vauxhall Crossland & Grandland X Club
Hi, does anyone have problems with stress fractures on the glass roof. The vauxhall garage is asking ÂŁ150 just to have a look. Any advice would be appreciated. Iv tried to contact relevant people but told its an insurance job. Thanks -
hi all i have a 2007 vectra c estate my front electric windows and mirrors are not working, also the passenger side button is not working either i managed to get the windows to go down with the keyfob but i cannot get them to go back up. i have checked all fuses and none are blown i dont think it can be the switch cause i would still be able to put them up with the keyfob. i have taken the door panel off no sign of corosion and its all still greased up still looks new. any other ideas what it could be ?
-
Sorry Howy I have no experience with caravan wiring only a simple boat trailer lighting board.
-
I have just changed the battery on it and when I go to start it there are no dashboard lights, I know that the battery is fine. What could be the problem. Mike
-
Hi, can anyone help locating a new manual glass sunroof for my 1996 corsa.
- Earlier
-
Hi everyone, Good to be here on my wife's behalf..I drive an old Landrover. Anyway, we've just bought a 2023 Crossland, 1.5d with 15,000 on the clock. I've read lots of reviews and so far, are quite happy with it. It obviously still has the Vauxhall warranty in place and the dealer's we bought it from. The only issue I have found is it's a little clonky on the gear change on the lower gear changes. Smooth as you like after that. Is this a common thing or is it because we're not used the clutch/gear change in this car. I used to be a driving instructor, so I can drive! Be grateful to hear your experiences on this. Thank you.
-
Hi, I couldn’t find any info on this either but have just fitted a set of aftermarket reversing sensors (Streetwise from Aldi) I lucked out and probed the positive wire first - Grey with green stripe and any random thin black cable I only probed two though. rear light cluster connector for me (clip on left) 1 - not used 2 - rear light + 3 - ground 4 - reverse light +
-
Hi folks. Stonham Barns is holding Vauxfest again this year. But this year they are allowing club stands too. If anyone is interested in attending the details are to follow.
-
Failed firmware upgrade
ALISON HARVEY replied to ALISON HARVEY's topic in Vauxhall Crossland & Grandland X Club
Thanks Jay. Will make an obvious mark somewhere! -
Anyone know how to reset parking sensors? On 2012 meriva
-
hello - same car and same year and same problem - did you get a resolve at all?
-
Can anyone tell me the caravan grey cable for fridge and battery charging colour of switched wires ignition off
-
Sluggish only when starting But keeps going from D1 D3D3 randomly automatic car
-
Hi, I have a 2019 Grandland X with intellilink 4.0 that is not working. I get the Vauxhall logo looping 5 or 6 times then goes to a blue software loading screen, again about 5 or 6 times then goes off completely. I haven't bricked it in any way to affect the start up script. I have tried updating it with the latest firmware from Vauxhall, but it does not work. I can see the USB flash drive is working by its light, but the system doesn't seem to be reading it after an initial second flashing. Any ideas what this could be before I spend a small fortune replacing it. Thank you